ASTM A666-10 PDF

ASTM A666-10 PDF

Dec 11, 2020 Relationship by admin

ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Temuro Daigul
Country: Luxembourg
Language: English (Spanish)
Genre: Marketing
Published (Last): 23 August 2009
Pages: 82
PDF File Size: 14.9 Mb
ePub File Size: 14.44 Mb
ISBN: 310-1-53546-949-1
Downloads: 24075
Price: Free* [*Free Regsitration Required]
Uploader: Darisar

a6661-0 Due to the high work hardening rate of these materials, intermediate anneals maybe required to successfully fabricate the part.

These alloys represent an excellent combination of corrosion resistance and fabricability. In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work.

and L Stainless Steel – NKS

Type L should astn used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Chemical Composition: One bend test shall be made ashm one end of each coil.

The values obtained in this manner should not, however, be taken as the actual yield strength for 0.

Material Test Report and Certi? Types and L are weldable by most fusion or resistance welding techniques.

  LIMES TRIPOLITANUS PDF

B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties.

Originally approved in Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

304 and 304L Stainless Steel

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Only annealed conditions of grades speci? The noncontrolling factor normally will exceed considerably the speci?

If filler metal is required, Type is normally used. Hard Elongation in 2 in. In case of dispute, the offset a66-10 of determining yield strength shall be used. Rockwell B 95 95 A — 10 Standard Speci?

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Number of Tests 8. Last previous edition approved in as A — The choice of test method for materials in conditions other than annealed shall be at the option of the seller.

Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

  ENFEITIADAS JESSICA SPOTSWOOD PDF

Maximum unless otherwise indicated. This revision of Speci? Chemical astmm and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres. Specimens shall be bent around a diameter equal to the product of the bend x666-10 times the speci? C Annealed material that naturally meets mechanical properties may be applied.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Type L should be used in heavier sections to reduce the occurrence aa666-10 carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: HardC Elongation in 2 in.

A number in parentheses indicates the year of last reapproval.

HRC typical L Ann 25 min. Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld.

This standard has been approved for use by agencies of the Department of Defense. Your comments will receive careful consideration at a asmt of the responsible technical committee, which you may attend.