This standard is issued under the fixed designation D ; the number immediately This test method was adopted as a joint ASTM–IP standard in operator prepares and inserts the beakers (with test oil, covers, and stirrers) into the bath as per ASTM D method. The test rod assembly (includes the steel. Model is a 6 test positions agitated liquid bath conforming to ASTM D, D, D, NACE TM and other similar tests. A timer alerts the.
|Published (Last):||17 November 2017|
|PDF File Size:||7.72 Mb|
|ePub File Size:||14.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
A clear plastic safety guard is available as an option on the front of the apparatus protecting the operator from the rotating stirrer shafts. Manual Liquid Bath for Rust Testing, 6 positions.
ASTM D Rusting Characteristics of Petroleum Products
The design chuck is as specified by the test method. This test method is also used for testing other oils, such as hydraulic oils and circulating oils.
A secondary high temperature limit switch prevents over heating in the event of primary controller failure. Silicone carbide paper grit 50 sheets. Work Item s – proposed revisions of this standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. Note 1—For synthetic fluids, such as phosphate ester types, the plastic holder and beaker cover should be made of a chemically resistant material, such as polytetrafluoroethylene PTFE.
A timer alerts the operator to method critical steps requering attention. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
This test method is also used for testing hydraulic and circulating oils, including heavier-than-water fluids. The individual stirrers are belt driven. Holding chuck for polishing test specimen. Link to Active This link will always route to the current Active version of the standard.
Rust Preventing Characteristics Oil Bath – Koehler Instrument Company, Inc.
This test method is also used for testing other oils, such as hydraulic oils and circulating oils. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Polishing device with chuck Volts. Historical Version s – view previous versions of standard. The advantage of the these aluminum baths over a liquid bath is the safety with the elimination of fumes and fire hazards if using oil as the bath medium. Link to Active This link will always route to the current Active version of the standard.
It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Work Item s – proposed revisions of this standard.
Rust-Preventing Characteristics of Mineral Oil – ASTM D665, D3603, D7548 | NACE TM-01-72 | IP 135
The test beakers rest on a perforated support rack at the d65 specified level. For specific warning statements, see 6.
Clear plastic stirrers’ shield for 4 position baths. The stainless steel bath has drain for easy replacement of the bath medium. FTM Paddle and Shaft. Referenced Documents purchase separately The documents listed d6665 are referenced within the subject standard but are not provided as part of the standard. Beaker cover for D and D, each. When lifted, the stirrer shaft protrudes through the top of the apparatus, allowing full and easy access to the test beaker.
Provision is made in the procedure for testing heavier-than-water fluids. This test method was used as a basis for Test Method D Qstm is identical to Model but with only 4 test positions.
Water beaker for D Part B, each. It is used for specification of new oils and monitoring of in-service oils. Specifications subject to change without notice. No other units of measurement are included in this standard.
C0 Standards Related Products 1. For specific warning statements, see 7. Each position is individually temperature controlled and independent of other positions. A protective cover is provided over the motor. Model A is an aluminum dry bath with 4 positions. Steel test specimen for D, each. This feature, unlike conventional aluminum block baths allows precise temperature adjustment. In addition, a float switch interrupts power to the heaters in the event of low bath liquid level.