ENDA ETC 9420 PDF

ENDA ETC 9420 PDF

Jul 20, 2020 Technology by admin

NOTE: ETC ENDA ETC series are intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding. Thank you for choosing ENDA EPC profile controller. * Selectable SSR or While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive. Double set point. Selectable sensor type (Pt, J, K, L, T, S, R). PID control function with accurate self-tuning. Digital inputs can be assigned to 3 different.

Author: Arashura Fegami
Country: Somalia
Language: English (Spanish)
Genre: Love
Published (Last): 19 September 2009
Pages: 300
PDF File Size: 8.21 Mb
ePub File Size: 19.79 Mb
ISBN: 482-2-86801-941-1
Downloads: 73813
Price: Free* [*Free Regsitration Required]
Uploader: Arat

Read this document carefully before using this device. Enter PID parameters of the system if they are known at the begining. Otherwise, Self-Tune should be activated. RS Modbus communication None Relative humidity According to EN Front panel: IP65 Rated population degree Rear panel: Process value during enxa operation Mnemonic parameter code during programming SV Display: Set point during normal operation Date value during programming SET Do not use the device in locations subject to corrosive and flammable gases.

Selectable logic control output. Adjustable between 1 and seconds. While cleaning the device, solvents thinner, benzine, acid etc. Make sure that the device is used only for intended purpose.

Enda ETC Series PID Temperature Controllers Panel Mount | Rapid Online

The shielding must be grounded on the instrument side. During an installation, all of the cables that are connected to the device must be free of energy. The 94420 must be protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation temperature is not exceeded. All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables.

These cables should not be close to the power cables or components. The installation and electrical connections must be carried on by a qualified staff and must be according to the relevant locally applicable regulations. When 2 wired Pt is used, terminals that are shown at the right of there must be short circuited for each product. Use suitable compensation cables. Pay attention to the polarities of the thermocouple cables as shown in the figure right are connected to the.

  ESPIRITUALIDAD ESENCIAL ROGER WALSH PDF

Therefore, when using a grounding thermocouple, do not connect the logic output terminals to the ground. Set appears on the display. Then, the value is adjusted by using PV A1. Then, the ehda is adjusted by using If C. S different from out1. The maximum of C. SEt is the value of C. If independent alarm is selected, A1.

Technical Specification

If deviation alarm is selected, A1. If band alarm is selected, A1. If this parameter is set to 0, the output power becomes 0 at the set point. Using this parameter the energy requirements of the system is adjusted at the set point. So the set point can be achieved by minimum fluctuations and in the shortest time. If independent or deviation alarm is selected, this parameter can be Lo. Four kinds of functions can be selected. CSET If key is pressed and held 0.

Technical Specification |

If waited enough,the value increases at each step. After 1 second following the release of the key, initial condition is returned. The same procedure is valid for the decrement key. Adjustable between 0 and minutes. If 0 is selected, soft start feature will be enable and the device reaches set point value quickly. If this parameter is adjusted to a value closer to the energy requirements of the system at the set point, process temperature is prevented to rise or drop to dangerous levels.

Press any key to deactivate the self-tune procedure. After PID is calculated A. It should be If process value is Appropriate to begin self tune, rEdY. Then press any key to see Pid. While holding 25 REdY. Selectable, and Adjusable between 1 and Difference addresses should be selected for every device.

  INTRODUCTION TO MODERN PHYSICS RICHTMYER PDF

If any key is pressed while P.

Before self tune procedure, A. If self tune is achieved A. Before self tune procedure, temperature setpoint value should be adjusted. When self tune procedure begins with no failure, Pid.

When PID parameters are Filter for display value. Adjustable between 1 and If this parameter is 1, digital filter runs most quick. Then the device heats until setpoint value according to PID parameters and calculates the energyrequirement for stable If the parameter is 31, the filter run most slow.

The value 99420 parameter should be increased in interference. The maximum value is the value of A2. The maximum eyc is the value of A1. If the temperature unit is changed, the value of the UPL. IfInp parameter is selected TC or Pt, this parameter is seen.

UnIt Offset value is added to the measurement value. The normal value is 0. The maximum value is the value of C. The minimum value is the value of C. If the selected input type is changed, the value of C. Alternatively, the same function occurs first pressing Entering from the programming mode to the run mode: If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered. It’s a community-based project which helps to repair anything.