BRU from EPCOS AG. Find the PDF Datasheet, Specifications and Distributor Information. epcos r datasheet, cross reference, circuit and application notes in pdf format. R ,92 MHz. Abstract: R epcos r SM r SAW R SAW R sm r R EPCOS r saw S M R Text: Competitor P/N (MHz).
|Published (Last):||12 October 2017|
|PDF File Size:||5.62 Mb|
|ePub File Size:||7.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
Epcos r – Montare motore elettrico
Imagine unlocking your car, g707 around some, and then being unable to lock it again. Good thing that mechanical locks are not totally uncommon. I still had one remote in spare though, and together with a bought new one the set was complete once again. I would guess that is pretty much the same for each car manufacturer, as are the inner workings.
All was well until another key broke down — same procedure, different day. But it made me wonder if it could be t707 — so I cracked it open. This picture was taken after the repair, which explains the flux residues. While there are other manufacturers like RFM, these models seem to be a pretty common brand for such keys as far as I have seen.
Inside the metallic-ceramic casing is a parallel LC resonance circuit which has been precisely trimmed for a specific resonant frequency.
The current types are mostly pin compatible to the old ones. Those resonators cost you a few cents at Farnell, but I would guess Digikey also has them.
Use the datasheets to get the correct one for your frequency and pin layout. They are a real pain eepcos the ass to solder by hand! But, to be fair, they were not really designed for it.
Use hot air or reflow techniques if you can, or else heat the ground plane from the side, OR remove e;cos resonator by applying a small amount of solder to the case top and heat it up completely. Take care not to rip the copper traces off the pcb, as the glue keeping them there becomes flexible when overheated.
To solder on the new one, place it onto the cleaned pads and flow solder underneath the pins from the side, for e707 pin individually. Do not heat the resonator for too long. I did it like this twice, but as said — pain!
As I epcoss out later, the resonator was perfectly working. I swapped it anyways — even swapped the old one back once I found the error — to make sure, but the real culprit was the HF output transistor which I have marked in the lower left.
How it works, in easy epcks The signal generated by the microcontroller is a digital pulse signal containing the remote code.
This signal is fed into the resonator through a resistor and a capacitor, and from the resonator back through said capacitor to the base of the output transistor. The resistor limits the output impedance of the controller pin to prevent it from clamping the transistor base to a r7077 voltage and allow the resonator to overlay an AC component onto the DC voltage.
Now, as the resonator…well…resonates at its designed frequency, excited by the impulse coming through the capacitor when the controller pin turns ON, the resonance waveform is coupled into the base of the transistor, which in turn amplifies it and pushes it out onto the antenna.
Imagine repeatedly hitting a tuning fork with a small hammer ecpos touching it to stop the vibration in a certain pattern while picking up eppcos generated sound epco a microphone to amplify it.
What you get is a high frequency signal during each high-level time of the remote code signal and no signal during each low-level time. This is called OOK, or on-off-keying. It can be seen as an extreme example of amplitude modulation AMand the principle is identical to the way TV remotes work — only that RF is used instead of IR light.
RF Components and Modules
There is a lot more theory behind this, you can look it up in dedicated books about high frequency circuits and transmitter circuits. As for this circuit, have a look at page 6 of the AppNote linked below. It eepcos a standard circuit that very closely resembles my remote key, plus a detailed function explanation. Back to the repair — checking the original transistor with a standard multimeter showed proper diode behaviour meaning it was a bijunction npn or pnp transistorbut this is not always sufficient for a diagnosis of a working device in HF circuits.
The output to the antenna the copper strip along the left edge appeared near-zero and the pulse signal after the coupling resistor was pretty deformed, too. In the end, you probably have to find out by trial and error. Owning a GHz scope greatly simplifies the task, of course. What you can measure, though, is the pulse signal from the controller. Now, to get a suitable replacement, you can either buy a transistor that works for frequencies epcoss to above the operating frequency of epcks device and has the same pinout — or you can simply go look for a cheap remote controllable wall socket, wireless weather station or the likes.
Whatever you choose should use the same frequency, of course, and run on batteries. The probability of finding a suitable transistor inside such a transmitting device is very high. This will be the one nearest the feeding point of the antenna, like in the picture above. I had to try two different transistors, the first one was probably already dead before transplantation I already wondered why I never used that remote control.
A second one worked like a charm! I have noted the designation of the found replacement in the picture above. If the range is much less, the transistor is most likely not up to the job. You will need to reassign the key to your vehicle according to the proper method designated by the manufacturer.