GRAPHTEC FC8000 MANUAL PDF

GRAPHTEC FC8000 MANUAL PDF

Nov 16, 2021 Music by admin

Vinyl Cutter Download Graphtec FC, Vinyl Cutter Machine Download Software Installation & Operation Manual in pdf ( MB) > Download Now. Manually Adjusting the FC ARMS Sensor Level for Glossy Media and Glossy Laminated Prints. When using some glossy media or when using glossy. View and Download GRAPHTEC FC Series user manual online. Cutting Pro . FC Series Plotter pdf manual download.

Author: Dogis Akinokus
Country: Latvia
Language: English (Spanish)
Genre: Business
Published (Last): 6 January 2017
Pages: 333
PDF File Size: 9.54 Mb
ePub File Size: 15.65 Mb
ISBN: 299-3-32835-322-6
Downloads: 24902
Price: Free* [*Free Regsitration Required]
Uploader: Takasa

Setting Regarding Interface Chapter 9: In case of stubborn stains, use a cloth that has been moistened in alcohol or in a neutral detergent diluted with water. If the loaded media is tilted as shown below, position of the scanned registration mark is shifted from the position where it should be. Press the [2] key ARMS. E It is over the setting graphhec of the Reset to smaller value.

GRAPHTEC FC8000 SERIES User Manual

Use it turned off for all other cases. Tool carriage will move away to upper right by continuously performing the same operation. The plotter’s interface conditions have changed. Setting the Acceleration Grapgtec the acceleration of the tool that is used in each of the tool condition numbers.

The blade might be damaged by moving the carriage outside the media under this condition.

Attaching the Loupe Operation Loosen the tool holder screw. Contents Of Operation From Menu Screen Icon of the corresponding operation button is displayed in the screen to change the setting values.

Graphtec Manuals and Drivers – SignWarehouse Product Support

The mark can be detected when the color of the mark has a reasonable contrast against the background. It makes it easier to confirm the cutting results if you perform this mannual after the cutting is completed.

  2904D JRC DATASHEET PDF

Cutting and creasing of printed graphics is possible even on the reverse side of the media. The sensitivity of the registration mark sensor is automatically set by measuring the reflective level of the marks of the actual media. Adjust the Blade Length Manually Optimal manuaal is not achieved unless the blade length is adjusted in accordance to the used media and the cutter blade. Decrease the value if the media is thin, and increase the value if the media is thick.

In that case, manua the command before using. E The plotter is defective. Aligning the Push Rollers This section describes how to alignment of the push rollers.

Setting Feed Speed for Pre Feed Automatic pre feed when cut data is received and the speed of media for pre feed in initial feed are set here. Operation Loosen the tool holder screw.

Setting will affect both ends, resulting the total width change will be double the set value. Supplement It cannot be set on the plotter. Move Away the Tool Carriage It is possible to move the tool carriage mm toward upper right. Especially for the corners where two straight lines meet, cutting becomes very hard because it cannot rotate smoothly. Page 21 Attach a media stocker to each of the left and right stand sides with two socket head graptec screws, using the Allen wrench.

Selecting ,anual Condition Tool mxnual can be set in 8 settings from 1 to 8. Press the [2] key SCAN. Such locations may impair the performance of the graohtec. This function is available in ARMS 5. Unplug the power cord from the socket Prohibited Number of the MARK TYPE2 is used when you would like to use as much area registration mark will be different for the possible on the media as cutting area.

  DIENSTGRADE BUNDESWEHR HEER PDF

Digits janual settings can be changed by pressing the [FAST] key. If any accessory is missing, contact your sales representative or the nearest Graphtec dealer.

Comments to this Manuals Your Name. E It has exceeded detection area Check the media. Also, be aware that continuous cutting with cross cut is not possible.

E Registration mark was not Redo the sensor level adjustment. Automatically Cross Cut Automatically Cross Cut It will automatically cross cut after cutting when the cutting is done with provided software.

Setting the Reference Angle The FC analyzes the cutting data, and controls the angle of the cutter blade tip if the change in the angles of the corner is large. Attaching a Tool When mounting the tool in the tool holder, push the tool all the way into the holder until its flange contacts the upper part of the holder and then tighten the screw firmly. Move the position of the light with strong scattered source.

Press the [1] key AREA. Following items are displayed in the default screen. Mounting The Stock Rollers Mounting the stock rollers Insert the stock rollers into the slots on the media stocker.

This Setting range of cross cut force is from 1 to It will be same speed as tool is lowered when AUTO is selected. Page 11 Chapter 7: